Ultrasonic tomographic velocimeter for visualization of axial flow fields in pipes

An ultrasonic tomographic velocimeter to provide quantitative images of axial flow fields in pipes is developed and presented in this work. To detect the flow in various directions and positions, a novel transducer configuration strategy is proposed. All-in-one transducers are mounted in two sectional planes of the pipe. In each plane, N transducers are equally spaced along the circumference. Overlapped propagation paths are introduced by the configuration strategy, and the influence of the vortex flow can be eliminated theoretically by averaging the line velocities of the overlapped paths. To achieve a fast detection speed, the projection data is collected via an electrical scan in a fan-beam mode. After rearrangement and interpolation of the projection data, the parallel beam filtered back projection (FBP) algorithm is implemented to reconstruct the axial flow field. Numerical simulations with the theoretical velocity profiles were performed. The compensation method for the vortex flow is proved to be effective and necessary, and the number of transducers required for reconstruction of common flow profiles was estimated. Accordingly, an ultrasonic tomographic velocimeter consisting of 2×12 transducers was fabricated. Experiments were conducted in the straight pipe and downstream of a single bend pipe and compared with the computational fluid dynamics (CFD) simulation results. As demonstrated, the ultrasonic tomographic velocimeter was capable of visualizing both symmetric and asymmetric axial flow fields with high reliability.     

大宗粉煤灰的综合利用及提质方案

对于大宗粉煤灰原灰进行分选加球磨机粉磨，同时添加合适的激发剂进行提质，可以生产出不同细度和活性的粉煤灰产品，提升粉煤灰在水泥及商品砼中的用量。介绍了某发电公司的粉煤灰处置现状，在此基础上，对商品砼的粉煤灰性能要求进行了大量市场调研，针对性地给出了该公司粉煤灰的提质方案，最后进行了提质粉煤灰的应用市场和产品竞争力分析。     

云冈矿采空区自然发火综合治理技术实践

针对云冈矿12#煤层8820、8822采空区出现CO泄漏事件,采用粉煤灰填充,构筑木板墙充填粉煤灰,配以墙体周边注马丽散堵漏;采用灌浆泵进行地面黄土灌浆,实施采空区灭火。通过对采空区自然发火进行综合治理,取得了良好效果,消除了自然发火隐患。     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

烧结时间对含铅玻璃制备微晶玻璃析晶及性能的影响

以铅玻璃与粉煤灰为原料，通过协同熔炼制备了微晶玻璃。通过XRD和SEM等手段研究了不同烧结时间下微晶玻璃的物相组成及显微结构，测定了微晶玻璃的密度、吸水率、维氏硬度和化学抗性。结果表明: 延长烧结时间对含铅玻璃加入量为40%(FG40)、50%(FG50)样品的晶相类型和晶化程度有影响，而对含铅玻璃加入量为60%(FG60)、70%(FG70)和80%(FG80)样品的影响较小。随着烧结时间延长，样品晶化程度提高，晶体长大，玻璃相减少。适宜的含铅玻璃加入量为50%~70%，对应的FG50、FG60、FG70样品最佳烧结时间分别为4 h、3 h、3 h。     

不同粒径改性粉煤灰对磷酸根吸附性能的影响

废水排放过量的磷导致水体污染日益严重，将粉煤灰通过化学改性制备成了水化硅酸钙吸附剂，研究了改性吸附剂对磷酸根的吸附效果。利用XRD, SEM及BET比表面积等手段对粒度分级前后的吸附剂进行表征，研究不同粒级吸附剂对磷酸根的吸附性能，并考察其吸附机理。结果表明，不同粒级的吸附剂其化学成分出现了明显的偏析现象，孔隙结构也差异显著。相比其他粒径下的吸附剂颗粒，颗粒粒径在50?75 μm时，吸附剂中钙和硅含量较多，铝、铁和镁含量较低，水化硅酸钙组分含量最高，且伴有含铝的托贝莫来石晶体出现，钙离子的增加使其可以与更多的磷酸根结合形成沉淀。同时此粒径下具有较高的比表面积及孔隙度，疏松多孔的结构为钙离子提供更多活性位点。当使用粒径在50?75 μm的吸附剂吸附磷酸根时，磷的饱和吸附量可达到17.1 mg/g，比未分级的吸附剂高19.58%。     

浅谈高压变频调速变压器及高压变频系统结构

介绍了高压变频调速变压器及高压变频器系统的基本原理及结构,详细论述了系统各组成部分的功能,并进行了举例说明。     

Design and synthesis of foam glasses from recycled materials

Recycling has emerged as an environmental key point due to the diminishing of natural resources and the generation of ever-increasing amounts of industrial solid wastes. Glass wastes are among the materials that attract great interest in the recycling concept. This work presents the results of foams production from four series of compositions. The first series comprises powders of a sodium-calcium-silicate sheet glass cullet as the main component, an alkali-earth aluminosilicate glass as an additive, and a reagent grade silicon carbide (SiC) powder as gassing agent. In the second series, the glass cullet was used in combination with fly ashes (FLA) as main components, while SiC waste from abrasive paper served as foaming agent. In the third and fourth series, carbonates (calcite and dolomite) were used for foaming powder mixtures composed of sheet glass cullet and FLA, and powdered cathode ray tube panel glasses, respectively. All the processing parameters, including the main components, the nature and content of foaming agents are shown to play a crucial role on the foaming ability and final properties of the glass foams.     

二滩拱坝初次蓄水的变位监测反分析

简要介绍了在二滩拱坝1998年5月初次蓄水期,通过拱坝垂线和监测网系统,用统计模型和确定性模型理论分析方法,建立了施加于坝体各作用量与坝体受作用后的效应量(变位)间的数学关系;并根据预先计算分析成果,提出了在初次蓄水运行中拱坝变位的参考预报值,实时对二滩拱坝实际工作状态作出安全评判。     

高保真电子管功放输出变压器的精确设计计算法

hi-end电子管功放音质优美绵厚,影响其音质的关键部件是输出变压器的电声性能,成为系统的喉舌。提出了一个新的方法,改变了以往粗略的估算法,使设计计算更合理﹑更科学﹑更实验化,成功解决了设计制造输出变压器的关键问题。